ME6006 DESIGN OF JIGS, FIXTURES AND PRESS TOOLS L T P C 3 0 0 3
OBJECTIVES:
• To understand the functions and design principles of Jigs, fixtures and press tools
• To gain proficiency in the development of required views of the final design.
UNIT I LOCATING AND CLAMPING PRINCIPLES: 8
Objectives of tool design- Function and advantages of Jigs and fixtures – Basic elements – principles of location – Locating methods and devices – Redundant Location – Principles of clamping – Mechanical actuation – pneumatic and hydraulic actuation Standard parts – Drill bushes and Jig buttons – Tolerances and materials used.
UNIT II JIGS AND FIXTURES 10
Design and development of jigs and fixtures for given component- Types of Jigs – Post, Turnover, Channel, latch, box, pot, angular post jigs – Indexing jigs – General principles of milling, Lathe, boring, broaching and grinding fixtures – Assembly, Inspection and Welding fixtures – Modular fixturing systems- Quick change fixtures.
UNIT III PRESS WORKING TERMINOLOGIES AND ELEMENTS OF CUTTING DIES 10
Press Working Terminologies - operations – Types of presses – press accessories – Computation of press capacity – Strip layout – Material Utilization – Shearing action – Clearances – Press Work Materials – Center of pressure- Design of various elements of dies – Die Block – Punch holder, Die set, guide plates – Stops – Strippers – Pilots – Selection of Standard parts – Design and preparation of four standard views of simple blanking, piercing, compound and progressive dies.
UNIT IV BENDING AND DRAWING DIES 10
Difference between bending and drawing – Blank development for above operations – Types of Bending dies – Press capacity – Spring back – knockouts – direct and indirect – pressure pads – Ejectors – Variables affecting Metal flow in drawing operations – draw die inserts – draw beads- ironing – Design and development of bending, forming, drawing, reverse redrawing and combination dies – Blank development for axisymmetric, rectangular and elliptic parts – Single and double action dies.
UNIT V OTHER FORMING TECHNIQUES 7
Bulging, Swaging, Embossing, coining, curling, hole flanging, shaving and sizing, assembly, fine Blanking dies – recent trends in tool design- computer Aids for sheet metal forming Analysis – basic introduction - tooling for numerically controlled machines- setup reduction for work holding – Single minute exchange of dies – Poka Yoke.
TOTAL: 45 PERIODS Note: (Use of P S G Design Data Book is permitted in the University examination)
OUTCOMES:
• Upon completion of this course, the students can able to design jigs, fixtures and press tools.
TEXT BOOKS:
1. Joshi, P.H. “Jigs and Fixtures”, Second Edition, Tata McGraw Hill Publishing Co., Ltd., New
Delhi, 2004.
2. Joshi P.H “Press tools - Design and Construction”, wheels publishing, 1996
REFERENCES:
1. Venkataraman. K., “Design of Jigs Fixtures & Press Tools”, Tata McGraw Hill, New Delhi,
2005.
2. Donaldson, Lecain and Goold “Tool Design”, 3rd Edition, Tata McGraw Hill, 2000.
3. Kempster, “Jigs and Fixture Design”, Third Edition, Hoddes and Stoughton, 1974.
4. Hoffman “Jigs and Fixture Design”, Thomson Delmar Learning, Singapore, 2004.
5. ASTME Fundamentals of Tool Design Prentice Hall of India.
6. Design Data Hand Book, PSG College of Technology, Coimbatore.
OBJECTIVES:
• To understand the functions and design principles of Jigs, fixtures and press tools
• To gain proficiency in the development of required views of the final design.
UNIT I LOCATING AND CLAMPING PRINCIPLES: 8
Objectives of tool design- Function and advantages of Jigs and fixtures – Basic elements – principles of location – Locating methods and devices – Redundant Location – Principles of clamping – Mechanical actuation – pneumatic and hydraulic actuation Standard parts – Drill bushes and Jig buttons – Tolerances and materials used.
UNIT II JIGS AND FIXTURES 10
Design and development of jigs and fixtures for given component- Types of Jigs – Post, Turnover, Channel, latch, box, pot, angular post jigs – Indexing jigs – General principles of milling, Lathe, boring, broaching and grinding fixtures – Assembly, Inspection and Welding fixtures – Modular fixturing systems- Quick change fixtures.
UNIT III PRESS WORKING TERMINOLOGIES AND ELEMENTS OF CUTTING DIES 10
Press Working Terminologies - operations – Types of presses – press accessories – Computation of press capacity – Strip layout – Material Utilization – Shearing action – Clearances – Press Work Materials – Center of pressure- Design of various elements of dies – Die Block – Punch holder, Die set, guide plates – Stops – Strippers – Pilots – Selection of Standard parts – Design and preparation of four standard views of simple blanking, piercing, compound and progressive dies.
UNIT IV BENDING AND DRAWING DIES 10
Difference between bending and drawing – Blank development for above operations – Types of Bending dies – Press capacity – Spring back – knockouts – direct and indirect – pressure pads – Ejectors – Variables affecting Metal flow in drawing operations – draw die inserts – draw beads- ironing – Design and development of bending, forming, drawing, reverse redrawing and combination dies – Blank development for axisymmetric, rectangular and elliptic parts – Single and double action dies.
UNIT V OTHER FORMING TECHNIQUES 7
Bulging, Swaging, Embossing, coining, curling, hole flanging, shaving and sizing, assembly, fine Blanking dies – recent trends in tool design- computer Aids for sheet metal forming Analysis – basic introduction - tooling for numerically controlled machines- setup reduction for work holding – Single minute exchange of dies – Poka Yoke.
TOTAL: 45 PERIODS Note: (Use of P S G Design Data Book is permitted in the University examination)
OUTCOMES:
• Upon completion of this course, the students can able to design jigs, fixtures and press tools.
TEXT BOOKS:
1. Joshi, P.H. “Jigs and Fixtures”, Second Edition, Tata McGraw Hill Publishing Co., Ltd., New
Delhi, 2004.
2. Joshi P.H “Press tools - Design and Construction”, wheels publishing, 1996
REFERENCES:
1. Venkataraman. K., “Design of Jigs Fixtures & Press Tools”, Tata McGraw Hill, New Delhi,
2005.
2. Donaldson, Lecain and Goold “Tool Design”, 3rd Edition, Tata McGraw Hill, 2000.
3. Kempster, “Jigs and Fixture Design”, Third Edition, Hoddes and Stoughton, 1974.
4. Hoffman “Jigs and Fixture Design”, Thomson Delmar Learning, Singapore, 2004.
5. ASTME Fundamentals of Tool Design Prentice Hall of India.
6. Design Data Hand Book, PSG College of Technology, Coimbatore.
